Add windows xp to lilo

You would also want to set aside an adequate amount of space for a Linux swap partition. The unwritten rule is to use twice the amount of RAM you have in disk space. A 64MB system would have MB of swap, and so on. Adequate swap space is the discussion of many flames on IRC and Usenet.

With your partitions laid out, you should proceed to install Windows. After that is set up and working, you should install Linux. The LILO installation needs special attention. You will want to select the expert mode for installing LILO. Begin a new LILO configuration. You will want to install it to Master Boot Record so that it can be used to choose between the two operating systems.

Once that's complete, you can install LILO. Reboot the computer. LILO should load and will display a menu letting you select between the operating systems you have installed. LILO is quite a configurable boot loader. It's not just limited to booting Linux or DOS. It can boot just about anything. Through mounting of the ntfs partion on the second drive with XP and the backup of the MBR I also could have mounted my linux partition or put the MBR on a floppy or usb stick.

There is a error in the message above. A workaround. After xp installation copy ntldr ,boot. Your email address will not be published.

Save my name, email, and website in this browser for the next time I comment. Get our Articles via Email. Cookies contain small amounts of information such as login information and user preferences and will be stored on your device.

Enable All Cookies Privacy Policy. I am a newbie in the Linux world. I installed Redhat at least tried doing a dual boot with XP.

Any help is greatly appreciated. Notice This topic is archived. New comments cannot be posted and votes cannot be cast. Responses to this topic. No need to apoligize, you did nothing wrong.

You did not hijack the thread. Your post explained your situation fine. Personally, I would leave the system alone, if it is functioning properly and you feel queasy about changing anything right now. To offset the delay of Win XP booting, just highlight it and hit the enter key. The 30 second boot delay will be be skipped. There is no delay, no countdown, and Windows will boot immediately. If you have already changed the previous install partition for RedHat and it is no longer there, the grub menu.

There is nothing to change, in this case. In this case, you need to resort to more drastic measures, hence my post on the Win 98 boot disk and the the command line to try and re-write the MBR. Some report this works, some report that it fails.

I believe this is due to the way the system was already set up. If this is an HP or Compaq system, I would leave it alone. OK, firstly, thank you to all those offering helpful advice. Secondly, I apologise for the thread hijack, as it was bound to cause confusion, but as I was searching the forum for info, this is the threaed that seemed most relevant, so I thought tagging this onto the end might melp others in my situation.

I presume that as I can now only boot into Windows, that editing the Grub. Create two partitions, then install Windows on one of them. Once you are done installing Windows on one partition, proceed with installing Xandros. Review and accept the license agreement and select Custom Install when you are asked to choose between the Custom or Express methods of installation.

On the Software Selection screen that follows, you should choose to install the Complete Desktop, since this will install most packages that one needs on a daily basis.

You will be presented with a screen where you can modify the partitions on your hard disk. Take care to leave sufficient free space for Fedora; I recommend 4GB or more. The next screen will show you the summary of disk configuration. LILO will be written to the Xandros root partition. Now complete the rest of the installation, and when prompted, remove the installation CD and reboot your system.

When asked what kind of installation you would want, select Custom Install. When presented with the disk configuration options, select Manually partition using Disk Druid. Xandros will probably not be listed.

Click on the Add button, and in the window that pops up, enter Xandros in the Label field and the devicename of the Xandros partition which you noted earlier in the Device field. Now complete the rest of the installation steps, and when prompted, remove the installation CD and reboot the system.