Copystar cs 3035 manual

U Setting the service telephone number Description Sets the telephone number to be displayed when a service call code is detected. Purpose To set the telephone number to call service when installing the machine.

Method Press the start key. U Copying without paper Description Simulates the copy operation without paper feed. Purpose To check the overall operation of the machine. Method 1. Press the start key. The screen for selecting an item is displayed. Purpose To check the part number or to decide if the ROM version is new from the last digit of the number. U Initializing backup memory Description Initializes only the data set for the optical section or initializes various setting data when installing the optional network scanner board.

Purpose To be executed after replacing the scanner unit or installing the network scanner board. Start Press the start key. U Checking motor operation Description Drives each motor. Purpose To check the operation of each motor. Select the motor to be operated. The selected item is displayed in reverse and the operation starts. U Checking clutch operation Description Turns each clutch on. Purpose To check the operation of each clutch. Select the clutch to be operated. The selected item is displayed in reverse, and the clutch turns on for 1 s.

U Setting folio size Description Changes the image area for copying onto folio size paper. Purpose To prevent the image at the trailing edge, or right or left side of the paper from not being copied b y setting the actual size of the folio paper used. U Performing fine adjustment of the motor speed Description Performs fine adjustment of the speeds of the motors. Purpose Used to adjust the speed of the respective motors when the magnification is not correct.

U Adjusting the scanner input properties Description Adjusts the image scanning density in text, text and photo, or photo mode. Purpose Used when the entire image appears too dark or light. The screen for executing is displayed. Setting 1. U Adjusting the shading position Description Changes the shading position. Purpose Used when white lines continue to appear longitudinally on the image after the shading plate is cleaned.

This is due to flaws or stains inside the shading plate. To prevent this problem, the shading position should be changed so that shading is possible without being affected by the flaws or stains. Purpose To be executed if the correct magnification is not obtained in the auxiliary scanning direction when the optional DP is used. Caution Before making this adjustment, ensure that the following adjustments have been made in maintenance mode.

Purpose To be executed if there is a regular error betw een the leading or trailing edges of the original and the copy image when the optional DP is used. Purpose To be executed if there is a regular error betw een the centers of the original and the copy image when the optional DP is used.

U Checking scanner operation Description Simulates the scanner operation under arbitrary conditions. Purpose To check scanner operation. Select the item to be changed. The selected item is displayed in reverse. U Executing DP automatic adjustment Description Uses a specified original and automatically adjusts the following items in the DP scanning section. Purpose When performing respective image printing adjustments, used to check the machine status apart from that of the scanner with a non-scanned output MIP-PG pattern.

U Checking shading Description Performs scanning under the same conditions as before and after shading is performed, displaying the original scanning values at nine points of the contact glass. Purpose To check the change in original scanning values before and after shading.

The results may be used to decide the causes for fixing unevenness uneven density of the gray area of an image: either due to optical shading or CCD or other problems. U Adjusting the scanner automatically Description Makes auto scanner adjustments in the order below using the specified original.

U Setting the exposure density gradient Description Changes the exposure density gradient in manual density mode, depending on respective image modes text, text and photo, photo, text in fax mode, photo in fax mode. Purpose To set how the image density is altered by a change of one step in the manual density adjustment. U Setting:Density in photo mode 1. Select the item to be adjusted. U Initializing original size Description Checks the operation of the original size detection sensor and sets the sensing threshold value.

Purpose To adjust the sensitiveness of the sensor and size judgement time if the original size detection sensor malfunctions frequently due to incident light or the like. U Checking the operation of main high voltage Description Performs main charging.

Purpose To check main charging. Purpose To check the drum surface potential. U Setting toner refresh operation Description Sets the drum refresh operation time and the developing bias on time at power on and after copying. Purpose To change the drum refresh operation time and the developing bias on time at power on and after cop ying if image flow level is low. The value is set, and the screen for selecting an item is displayed. U Displaying the drum history Description Displays the past record of machine number and the drum counter.

Purpose To check the count value of machine number and the drum counter. U Checking sensors and switches for toner Description Displays the on-off status of each sensor or s witch related to toner. Purpose To check if the sensors and s witches operate correctly. A list of the switches, the on-off status of which can be chec ked, are displayed.

U Setting the fixing control temperature Description Changes the fixing control temperature. Purpose Normally no change is necessary. However, can be used to prevent curling or creasing of paper, or solve a fixing problem on thick paper. U Stabilizing fixing forcibly Description Stops the stabilization fixing drive forcibly, regardless of fixing temperature.

Purpose To forcibly stabilize the machine before the fixing section reaches stabilization temper a ture. U Setting the fixing phase control Description Sets the use of fixing phase control to reduce electr i cal noise generated by the copier. If electrical noise generated by the copier causes flickering of the lights around the copier, select fixing phase control to reduces the noise. Purpose To check if all the LEDs on the operation panel light. All the LEDs on the operation panel light.

Purpose To check the DP. Place an original in the DP if running this simulation with paper. U Setting the presence or absence of the coin vender Description Sets the presence or absence of the optional coin vender. Also sets the details for coin vender operation, such as mode and unit price. This is an optional device which is currently supported only by Japanese specification machines, so no setting is necessary.

U Checking the operation of the DP motors, solenoids and clutch Description Turns the motors, solenoids or clutch in the optional DP on. Purpose To check the operation of the DP motors, solenoids and clutch. U Method for the volume switch 1. Move the original insertion guides to check the detection status of the original size width switch. The detected original width is displayed as a numerical value with the decimals omitted.

Numerical Original width to be detected value U Checking messages Description Displays a list of messages on the touch panel of the operation panel. Purpose To check the messages to be displayed. Select the item to be displayed. Upper side is longer. Lower side is longer. Decrease the preset value. The value is set. U Checking the operation of large paper deck and paper feeder Description Turns on motors and clutches of optional large paper dec k or paper feeder.

Purpose To check the operation of motors and clutches of paper f e ed device. Start 1. U Checking the paper ejection to optional devices Description Ejects paper to an optional mailbox or job separator, or to the ejection slot at the machine left.

Purpose To check paper conveying operation to optional paper eject devices or the ejection slot at the machine left. Purpose To check the maintenance count. Also to clear the count during maintenance service. The maintenance count is displayed. Clearing 1. U Switching between double and single counts Description Switches the count system for the total counter and other counters. U Setting auto clear time Description Sets the time to return to initial settings after copying is complete. Purpose To be set according to frequency of use.

Set to a comparatively long time for continuous copying at the same settings, and a comparatively short time for frequent copying at various settings. U Changing the copy count timing Description Changes the copy count timing for the total counter and other counters.

Purpose To be set according to user copy service provider request. If a paper jam occurs frequently in the finisher when the number of copies is counted at the time of paper ejection, copies are provided without copy counts. Purpose Sets the code when replacing the main PCB and the like. U Setting auto application change time Description Sets the time that passes until the machine starts automatically printing after completing copying or operation when the machine is used as a printer or fax only if the printer kit or fax kit is installed.

Purpose According to user request, changes the setting. U Side ejection setting Description Sets whether to eject to the side of the machine when an optional cur l eliminator is installed. Purpose Set according to the pref e rence of the user. U Setting the ejection restriction Description Sets or cancels the restriction on the number of sheets to be ejected continuously when the internal eject tray is selected as the eject location.

Purpose According to user request, sets or cancels restriction on the number of sheets. Purpose According to user request, selects which has priority, the recovery time from preheat or energy saver.

Purpose Used if margins are not correct when the optional DP is used. Purpose To return to a setup at the time of factory shipments. This maintenance mode is eff e ctive for only V specifications. Purpose To check the time to replace consumab le parts. Also to clear the counts after replacing the consumab le parts. Purpose Sets the punch limit to notify the user of the time to collect punch-hole scr ap. Also, used to manually clear the punch-hole scrap count if a message requiring collection of punch-hole scrap is shown on the touch panel after collection.

Purpose To check the service call code status by types. Also to clear the service call code counts after replacing consumable parts. U Resetting partial operation control Description Resets the service call code for partial operation control.

Purpose To be reset after partial operation is performed due to problems in the drawers or other sections, and the related parts are serviced. Purpose To store and write data when replacing the PCB. U Checking the copy counts Description Checks the copy counts. Purpose To check the copy counts. The current counts of copy counter, printer counter and fax counter are displayed.

U 8. Then, downloading of the fax fonts starts and the result shown below is displayed. U Setting the type of cooling fan Description Sets the new or old type of cooling fan. Purpose To change the setting according to the type of the cooling f a n.

The screen for selecting an item is displa yed. U Setting the type of fixing unit Description Sets the type of fixing unit. Purpose To change the setting according to the type of the fixing unit. Purpose To check duration of use of the exposure lamp. Also to clear the accumulated time for the lamp after replacement. Purpose When performing respective image printing adjustments, used to check the machine status apart from that of the scanner with a non-scanned output VTC-PG pattern.

Paper misfeed counts sorted by the detection condition can be checked in maintenance item U To remove paper jammed in the copier, open the front cover, conveying cover, side cover or drawer. Jam in the mailbox 1 See the mailbox service manual. Jam in the mailbox 2 See the mailbox service manual. A paper jam in the is extremely curled. A paper jam in the deck is extremely curled. Run maintenance item U and turn feed switch 2 on and off A paper jam in the manually.

Replace feed switch 2 if indication of the correspond- paper feed section ing switch on the operation panel is not displayed in reverse. Run maintenance item U and turn feed switch 3 on and off A paper jam in the manually. Replace feed switch 3 if indication of the correspond- paper feed section ing switch on the operation panel is not displayed in reverse.

Check the status fixing section is indi- and remedy if necessary. Run maintenance item U and turn the feedshift switch on is indicated during and off manually. When a problem is detected, copying is disabled and the problem displayed as a code consisting of "C" followed by a number between and , indicating the nature of the problem.

A message is also displayed requesting the user to call for service. C Abnormal detection of fax control Defective fax Install the fax software to Ver. If none, s, 1 s after the drive motor has turned connector termi- remedy or replace the cable. While the cleaning lamp is on, the bro- lamp.

Defective drum Replace the drum unit. See page See page See page See page 8 One side of the copy 5 A white line appears 7 A black line appears 6 A black line appears No transfer charging. No LSU laser is output. No developing bias is output.

The connector terminals of the high-voltage Reinsert the connector. Also check for continuity within the connector cable. No main charging. Exposure lamp fails to light. Broken main charger wire. Replace the main charger unit. Leaking main charger housing. Clean the main charger wire, grid and shield. Insufficient toner. Deteriorated toner. The transfer voltage is not output properly. Dirty main charger wire. If the display shows the message requesting toner replenishment, replace the cartridge.

Dirty contact glass. Dirty or flawed drum. Deformed or worn cleaning blade. Dirty scanner mirror. Clean the contact glass. Dirty drum separation claws. Dirty heat roller separation claws. Perform the drum refresh operation. Feed clutch, paper feed clutch, bypass paper cally misaligned with feed clutch or registration clutch installed or the original. Feed clutch, paper feed clutch, bypass paper Check the installation position and operation of the feed clutch, feed clutch or registration clutch installed or paper feed clutch, bypass paper feed clutch and registration clutch.

Paper damp. Paper creased. Drum condensation. Flawed drum. Check the paper storage conditions. Replace the paper. Misadjusted center line of image printing. Misadjusted scanner center line. Original placed incorrectly. Readjust the center line of image printing see page The machine does outlet. If not, does not operate. Broken upper lift motor Check for continuity across the coil. If none, replace cooling fan Cooling fan motor 5 coil. Poor contact in the cooling Reinsert the connector. Also check for continuity within the con- fan motor 5 connector ter- nector cable.

Check for continuity across the coil. If none, replace feed clutch Feed clutch 3 does not operate. Poor contact in feed clutch Reinsert the connector. Also check for continuity within the con- 3 connector terminals. If none, replace the toner The toner feed sole- coil. Also check for continuity within the con- operate. Transfer charging is voltage transformer PCB not performed. Defective main PCB. Defective high-voltage transformer PCB.

See page No developing bias Defective high-voltage is output. Also check for continuity within the con- The size of paper in paper length switch con- nector cable. If none, remedy or replace the cable. No primary paper feed. Check if the developing unit is extremely Clean the developing unit. The selected maintenance item is run. Open the front cover and pull out the upper and lower drawers. Remove the two stop rings.

Stop rings 7. Pull the paper feed shaft toward the rear of the primary paper feed unit in the direction of the arrow and remove the paper feed pulley. Remove the four screws holding the lower right cover and then the cover. Raise the bypass separation shaft as shown in the diagram, remove the holder plate and the bushing, and then remove the bypass Holder plate separation pulley.

Raise the bypass paper feed shaft as shown Stop ring in the illustration, remove the stop ring, and Bypass paper feed shaft then remove the bypass paper feed pulley. Remove the stop ring of the bypass paper Stop ring Bushing feed shaft and slide the bushing in the direction of the arrow.

Bypass paper feed shaft Figure Slide the bypass forwarding pulley shaft Bypass forwarding pulley shaft temporarily toward the rear side and then raise it to remove from the bypass unit.

Remove the stop ring and slide the bypass forwarding pulley with the forwarding pulley Stop ring retainer from the shaft to remove it.

Replace the bypass separation, bypass paper feed and bypass forwarding pulleys. Bypass forwarding pulley Forwarding pulley retainer Figure Bypass paper feed shaft U U U U U U U U U U P. If the margins are still incorrect, perform the above adjustments in maintenance mode. The kyocera download centre is very easy to use. Copier at the printer scanner, cs Copier printer pdf manual, people at a download.

It was founded as kyoto ceramic company, cs How to economically manage the ejection cover. Around the cs compatible printers to solve unique challenges.

We delete comments that violate our policy, which we encourage you to read. Kyocera copystar cs driver - select or type the specific product you're looking for from the products drop down optional. How to exceed customer service manuals are the optional original cover. From desktop printers and highest quality, 6. Page self-diagnosis 1 self-diagnostic function this unit is equipped with a self-diagnostic function.

If you're looking for, anytime. Kyocera document solutions offers an award-winning range of device technology and integrated business process improvement solutions that work together seamlessly.

Copystar cs print driver download - with km-net viewer, administrators can oversee the network configuration, check paper levels, change device defaults, and view meter counts.

This toner cartridge prints pages. Cs all in one printer pdf manual download. Stuffed with advanced finishing options, this copystar cs copier delivers professional-looking output without compromising on the productivity of the machine.

Kyocera corporation is a japanese multinational ceramics and electronics manufacturer headquartered in kyoto, japan. The offer on this website is aimed exclusively at traders, companies, corporations and freelancers. Black for your brand name printer it won't let me. Currently you do not accept these cookies. Please check this box if you would like to.

Change language. Kyocera Worldwide. Download Center Access any files, from drivers to manuals, that you may need for your Kyocera product. FAQs Check out our most frequently asked questions to locate answers and find technical information. Contact Support Have more questions?